Planet Minis

Dave1rocks · 11-02-2009, 05:59 PM

Hello, mabey somebody can help me 1st off all I got a new stator, NO instructions included, 1 side goes to my points, condenser, coil. the other side goes knowhere because no lights or keyswitch at this time. How do I know with stator goes to which side one side has 2 wire comming off the other has 1 ground, 1 wire, 1 looping wire I know this sounds crazy but ?, I installed the one with one wire and the ground hooked it up to my points etc and my bike still wont run, by the way its a 1969 z50 No battery, Included is a diagram well sort of - can anybody help me?

misteroldskool · 11-03-2009, 08:13 PM

well i know that 3 wires go to the condenser, im not to sure on the rest, ill try and get some pictures tomorrow

misteroldskool · 11-08-2009, 08:13 PM

sorry it took a while for me get the picture, idk if you even still need it but ya here it is, there is one wire that you cant see, tis right under the condenser

Dave1rocks · 11-11-2009, 12:17 PM

Thanks for the picture I know how it hooks up know but still no spark - new stator new points, new condenser could it be my plug but it looks ok? do you mean the stator on the left that go's to the condenser too. The other side has 2 wires that go to the lights?

misteroldskool · 11-11-2009, 02:58 PM

if your still not getting spark it could be your coil, or even a bad spark plug

Dave1rocks · 11-12-2009, 04:33 PM

Hello I thinki my coil is good because I put a 6 volt power supply up to in and I get a good blut spark, mabey is it my plug because its been sitting a couple of years in storage,, thanks Dave

scpbmxer01 · 11-12-2009, 06:02 PM

put a tiny bolt ot screw in your spark plug wire hold the bolt and kick it over and see if you get shocked then you will know if its your coil or your plug.

Dave1rocks · 11-13-2009, 05:31 PM

OK, I put a bolt in the boot and I did not get shocked and I put a 6 volt power supply to the positive side of the coil and I get a good spark this so called stator I replaced said it was for a z50 but I believe it is aftermarket and the 2 stators or coils are as this - the Lighting coil has 2 wires coming off it and is slightly larger the other one has 1 single wire that is coming off it and another wire that is looped and partially insulated I know this sounds confusing but I contacted the person I received it from Ebay and they said 1 wire goes to the condenser and the other to the points and I tried it that way and no spark I always thought that like in the previous picture that 1 wire goes from the points to the condenser, 1 wire goes from the primary coil to the condenser and 1 wire comes off the condenser to the coil that goes to the plug. Does this make any sense to anyone?

mexicanyella · 11-13-2009, 06:36 PM

I need to pull the flywheel off one of my engines tonight; I'll try to refresh my memory on what goes where and post in the AM.

Dave1rocks · 11-14-2009, 03:22 AM

Thanks this is frustrating maybe the stator in not compatable. cant wait for your reply.

11-02-2009, 05:59 PM	#1 (permalink)
Dave1rocks PM Newbie Join Date: Oct 2009 Posts: 15	Z50 stator confusion Hello, mabey somebody can help me 1st off all I got a new stator, NO instructions included, 1 side goes to my points, condenser, coil. the other side goes knowhere because no lights or keyswitch at this time. How do I know with stator goes to which side one side has 2 wire comming off the other has 1 ground, 1 wire, 1 looping wire I know this sounds crazy but ?, I installed the one with one wire and the ground hooked it up to my points etc and my bike still wont run, by the way its a 1969 z50 No battery, Included is a diagram well sort of - can anybody help me? Attached Thumbnails

11-03-2009, 08:13 PM	#2 (permalink)
misteroldskool PM Newbie Join Date: May 2009 Location: Ventura CA Posts: 38	Re: Z50 stator confusion well i know that 3 wires go to the condenser, im not to sure on the rest, ill try and get some pictures tomorrow

11-08-2009, 08:13 PM	#3 (permalink)
misteroldskool PM Newbie Join Date: May 2009 Location: Ventura CA Posts: 38	Re: Z50 stator confusion sorry it took a while for me get the picture, idk if you even still need it but ya here it is, there is one wire that you cant see, tis right under the condenser

11-11-2009, 12:17 PM	#4 (permalink)
Dave1rocks PM Newbie Join Date: Oct 2009 Posts: 15	Re: Z50 stator confusion Thanks for the picture I know how it hooks up know but still no spark - new stator new points, new condenser could it be my plug but it looks ok? do you mean the stator on the left that go's to the condenser too. The other side has 2 wires that go to the lights?

11-11-2009, 02:58 PM	#5 (permalink)
misteroldskool PM Newbie Join Date: May 2009 Location: Ventura CA Posts: 38	Re: Z50 stator confusion if your still not getting spark it could be your coil, or even a bad spark plug

11-12-2009, 04:33 PM	#6 (permalink)
Dave1rocks PM Newbie Join Date: Oct 2009 Posts: 15	Re: Z50 stator confusion Hello I thinki my coil is good because I put a 6 volt power supply up to in and I get a good blut spark, mabey is it my plug because its been sitting a couple of years in storage,, thanks Dave

11-12-2009, 06:02 PM	#7 (permalink)
scpbmxer01 PM Newbie Join Date: Sep 2008 Location: rc Posts: 58	Re: Z50 stator confusion put a tiny bolt ot screw in your spark plug wire hold the bolt and kick it over and see if you get shocked then you will know if its your coil or your plug.

11-13-2009, 05:31 PM	#8 (permalink)
Dave1rocks PM Newbie Join Date: Oct 2009 Posts: 15	Re: Z50 stator confusion OK, I put a bolt in the boot and I did not get shocked and I put a 6 volt power supply to the positive side of the coil and I get a good spark this so called stator I replaced said it was for a z50 but I believe it is aftermarket and the 2 stators or coils are as this - the Lighting coil has 2 wires coming off it and is slightly larger the other one has 1 single wire that is coming off it and another wire that is looped and partially insulated I know this sounds confusing but I contacted the person I received it from Ebay and they said 1 wire goes to the condenser and the other to the points and I tried it that way and no spark I always thought that like in the previous picture that 1 wire goes from the points to the condenser, 1 wire goes from the primary coil to the condenser and 1 wire comes off the condenser to the coil that goes to the plug. Does this make any sense to anyone?

11-13-2009, 06:36 PM	#9 (permalink)
mexicanyella El rey de los puntos Join Date: Aug 2008 Location: Troy, MO Posts: 972	Re: Z50 stator confusion I need to pull the flywheel off one of my engines tonight; I'll try to refresh my memory on what goes where and post in the AM.

11-14-2009, 03:22 AM	#10 (permalink)
Dave1rocks PM Newbie Join Date: Oct 2009 Posts: 15	Re: Z50 stator confusion Thanks this is frustrating maybe the stator in not compatable. cant wait for your reply.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)