Mutant Motor Xr/klx

[doughboy83]

Looking good Chad.

[PlanetMinis.com]

[storminnorman07]

NICE Chad you posted up your set-up. Pictures equals knowledge

lol your the reason i decided to throw the lil video in there. as you see nothing special i was to cheap to buy a bhj. just couldnt justifie spending 1600 on a piston vise that at the time i thought i was only going to use a handful of times. which my home made one works great for what i need it for

[storminnorman07]

didnt get everything done to send to powder tomorrow, i think the only thing i have left to do is relocate rear brake pedal which i should have time this weekend to do and have ready for monday.

[skipbuysparts]

the oil cooler is nice. I thought about modding a air conditioning condenser for a oil cooler. how much did you spend on the ti valves? do you know of any ti valves that will work in a v2 head?

[klxadogg437]

Man Great Work! Looks Good

[storminnorman07]

the oil cooler is nice. I thought about modding a air conditioning condenser for a oil cooler. how much did you spend on the ti valves? do you know of any ti valves that will work in a v2 head?

i dont remember off hand i wanna say roughly 200 a valve. have not really looked into ti valves for a v2 if i remember the lil bit of looking i did over all length was to long.

[storminnorman07]

well guys the mutant lives! i would love to end this post with a nice video of it running but...... broke the kicker gear! after 3 or 4 kicks it fired up in a fit of excitment i reached for my phone to get a video and it stalled cause i had no set the idle yet. figured woo big sigh of relief it runs i'll grab my phone fire it up set idle then get a video. 2nd kick in strip. so now i get to try and figure out a cure for this or block it off and bump start it like everyone else does. but i'm lazy and really dont wanna have to push start this cochroach everytime i wanna ride it.

[skipbuysparts]

well guys the mutant lives! i would love to end this post with a nice video of it running but...... broke the kicker gear! after 3 or 4 kicks it fired up in a fit of excitment i reached for my phone to get a video and it stalled cause i had no set the idle yet. figured woo big sigh of relief it runs i'll grab my phone fire it up set idle then get a video. 2nd kick in strip. so now i get to try and figure out a cure for this or block it off and bump start it like everyone else does. but i'm lazy and really dont wanna have to push start this cochroach everytime i wanna ride it.

I have had good luck with a chainsaw decomp. you would probally be able to install one in about 5 minutes. it took me a couple hours. and I had to epoxy the hole. I used a hand drill and messed up. it still works realy well

[storminnorman07]

I have had good luck with a chainsaw decomp. you would probally be able to install one in about 5 minutes. it took me a couple hours. and I had to epoxy the hole. I used a hand drill and messed up. it still works realy well

one of those type of decomps? if so wont work on this head

[skipbuysparts]

one of those type of decomps? if so wont work on this head

yep I bought one from a chainsaw shop. its a little smaller and has a plastic button. well I hope something works. I cant wait to see it run.

[storminnorman07]

yep I bought one from a chainsaw shop. its a little smaller and has a plastic button. well I hope something works. I cant wait to see it run.

Basically the same thing just different knobs. I have looked into the push button already but due to the 4 valve design there's not enough room to throw one in the head with out interfering with something. I have a few places to call and get some info but I might have a fix not going to get to excited just yet til I get all facts straightstraight

[storminnorman07]

here is the carnage

[skipbuysparts]

DAMMIT!!! I would give it the finger too. hope you get it fixed soon. good luck

[storminnorman07]

DAMMIT!!! I would give it the finger too. hope you get it fixed soon. good luck

thank you ill need all the luck i can get. new gears should be tues next week i have a few tricks up my sleeve to try to get them to last longer. looking at the kitaco 4 valve came it looks really close if thats the case i believe there is a d-comp cam for it and with luck the kicker gears will last this time. upon tear down i seen some things with piston that i didnt care for and if i dont attend to it now its asking for a castrophic failure. so that means i'll also be changing rod and piston possbily crank and stroke haven't really sat down and figured everything out. needless to say its still going to be a hot min before i get to hear this beast run again

[j440]

any updates?

[storminnorman07]

any updates?

no i dont know why i bother asking companys when things are going to be done its never done when they say it will. i did get my tranny racks and kicker gears back from being treated but thats it. powder coat guy said it would be done this week just got off the phone with him a few mins ago yup hasnt even been looked at yet still sitting on the floor. he claims it will be done thurs or fri of this following week but my not holding my breath. and im still waiting on a piston.

[storminnorman07]

finally parts from p/c are done! i think piston should be in tomorrow. now its just a matter of getting some time to pi$$ with it

[doughboy83]

Looking good man!

[50rider340]

Hot dam two spokes down and so many to go lol. Orange and black kinda reminds me of a pumpkin ahha

[j440]

looking good. still super anxious to see the outcome!